So, I bit the bullet and decided to rebuild the Delco Moraine brake booster in my '63 Deville due to a super hard pedal. Thanks to the many forum discussions on this site, I got it apart with no issues (and I'll post the removal tool I built later in another post and lend it to anyone who needs it).  Unfortunately, I realized that I am missing the "support plate seal retainer" (see picture) that looks like it goes between the booster and the master cylinder. I believe the booster is original and has never been apart as the car only has 57k miles on it so that means I'm probably the culprit for the lost piece. When I got the car, the master cylinder was dry and rusted inside. I replaced it with a newer style master cylinder and, unfortunately, threw out the original master cylinder (and I usually keep EVERYTHING). I'm guessing the support plate seal retainer was probably on the original master cylinder and I probably trashed it along with the master cylinder. Is that possible to do or would that retainer plate been pretty obvious and split apart from the old master cylinder? Also, I'm guessing that plate/seal is required to hold the vacuum in the booster? Also, without that plate, could that have been why I had no power brakes because of no vacuum in the booster? All that said, does anyone have a support plate seal retainer for a Delco Moraine that they'd be willing to sell?

Views: 131

Reply to This

Replies to This Discussion

Thanks for the reply but these are definitely too hard and not normal - I almost have stand on the pedal. After more research, I think I'm definitely missing that support plate seal retainer. I'm hoping someone can come to my rescue and either sell me just that support plate from an old, damaged booster or even sell me a whole booster that I could rob that part from.



  • Add Photos
  • View All


Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 1 hour ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Pertronix 3 install and resistor wire

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 1 hour ago. 15 Replies

A few questions on the resistor wire, what color is it in the pic? The yellow/blue or black? And connecting to the ACC on the fuse box seems easiest way to go with the new switched wire, but where…Continue

Cruise control

Started by CHRIS CARLSON in 1963/64 Cadillac Specific Discussion. Last reply by Mike Travers 3 hours ago. 1 Reply

Is anyone using an aftermarket cruise control on there 64 Cadillac? what brand & model did you purchase?Continue

carter carb paper gaskets

Started by tim sparks in General Discussion 4 hours ago. 0 Replies

had my carter carb on my 63 rebuilt when i got it back rebuilder gave me 2 rochester paper gaskets according to the ones jason sells.will those be a problem putting them on my carter? thanks in…Continue

Blog Posts

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…


Clock ‘64 DeVille

Posted by Matt Vander Hooven on July 23, 2023 at 7:36pm 2 Comments

Is there still a member in the Detroit area that refurbishes clocks?

Matt VH

Spark Plug Heat Range

Posted by Patrick Westphal on July 7, 2023 at 10:00am 1 Comment

I found a diagram that illustrates the main factor in determining a spark plug heat range that I was trying to describe to you during the chapter get together.

Here it is:


The main factor is the length of the ceramic insulator from the middle of the spark plug to the tip (where the spark happens)  

The insulator…



  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service