I recently disassembled the right door of my '63 convertible to do a bunch of maintenance and restoration on several of its components. The door panel had not been particularity tight to the door, and I was not sure of the best way to re-assemble it with the nails/pins that hold the two sides of the panel to the door. I knew I could just use small nails, but it seemed these were not a great option. I did some searching, and the only alternative I found were the door clips show below, listed on eBay. I gave them a shot and they worked great.  (Plus it is only $14,19 for a set of 10 clips which does one door). I've ordered another set for my other door.

I have no connection to the seller, I'm just passing along the info in case others are facing a similar re-assembly challenge.

https://www.ebay.com/itm/192553041159

I think they were actually intended to clip over the thicker fiber/cardboard panel of the door panel, but that would have required me to make more adjustments to the vinyl covering than I wanted to make. Instead, I clipped them to the steel frame that runs around the panel. Everything lined up fine this way, so maybe that is how it is intended to be done. Here is how I did it:

1. I could find all the old nail holes (where the welds broke) or welds in the steel edging from the original nails and I marked their location in pencil on the inside of the door panel

2. I bent the clip part of the faster (just with my fingers) to create a narrower slot with about a 1/16" to 1/8" gap

3. I slid the faster over the steel edging at the pencil marks. The solid side of the clip faces the center of the door panel and the open side of the clip faces the edges of the panel. The pencil marks give you the up/down alignment on the door panel, and you have about 1/2" of up and down tolerance because the slots the nails go into on the door are about that length. For a few fasteners, I needed to make small cuts in the clips or in the door panel vinyl to get them to fit onto the steel frame well. These adjustments were easy to figure out and simple to do. I just cut the clips or vinyl with diagonal pliers.

4. Most mounted clips were plenty tight on the steel of the door panel, but I squeezed a few tighter just using a pair of pliers.

5.  I slipped the top of the panel over the top of the door and then just pushed the panel in top to bottom. I had two slide a few clips up or down a small amount, but this was also easy. The nail part is a ring-shank type nail, so they hold securely.

Before re-assembly, I took this picture of the inside of the door panel with the clips mounted. You can see the clips and pencil marks along the side edges of the door (click on the picture to go to full size). - Now I wish I had snapped a close up! The two clips near the top of the picture (which is the bottom of the door) and those on the right side of the picture are reasonably visible in the full size pict.

Views: 537

Reply to This

Replies to This Discussion

Karl, this is great info. the original nails were ring shank type nails as seen in the male end part of your fasterners. I would how they look from the front and back and basically how they attach since the original nails just pushed straight thru the metal ridge and into the plastic insert in the door. These look like they would just press back into the blastic inserts but am having a har time picturing how the U shaped "head" attached to the door panel without being exposed?

Thanks for the tips - Fortunately I did all of this except the hinge grease, which I can do without taking things apart. Any suggested grease - If not I'll likely just use a lithium grease

Karl, this is really fantastic & helpful info and the way you just clip on the steel frame makes perfect sense! I hope you don't mind but I moved your details into the main post at top so it doesn't scroll out of site if we get a lot of replies. I also added a link and gave you credit on our Help Page under Door Panel Clips. I would also like to include in our next newsletter in the Tech Tips section. 

I'm always happy when I can contribute anything back to this group as I've learned a ton from other members here - letting me enjoy making basic fixes to my car and saving me some $ too!

ps. I just ordered 2 sets!

RSS

Photos

  • Add Photos
  • View All

Forum

What To Do With Those Damn Coil Springs?!

Started by Jason Edge in General Discussion. Last reply by Dennis P. DiBari 7 hours ago. 4 Replies

Coil Springs is one part I generally do not sale (who wants a tired used coil spring), but it is also one of those items I just can't let go up. I have painted them, stuck lights in them, put them…Continue

Too Cold to Do Much with Dino Right Now

Started by Jason Edge in General Discussion yesterday. 0 Replies

North Carolina can be pleasant in the winter, with temps mild (60's/70's in the day and 40's and 50's at night); however, yesterday when I got up it was 20, and the has been in the mid 40's, Today it…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Thursday. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

64 cadillac deville convertible interior

Started by Larry Rees in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge on Tuesday. 1 Reply

Hello everyone. I am trying to sort out a interior order that came to me with the wrong diamond pattern and no buttons. They are going to fix it but I would like to include some pictures of the…Continue

Blog Posts

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

Videos

  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service