My front door handle lights would not go on when I opened the doors. Bulbs were good and had power to them. Was not getting a ground. The door switch was corroded and wasn't making contact when the door was opened. Bypassed the switch and the lights are working. Good so far. (Jason, do you have extra switches for sale?)

The map light wasn't working due to a burned-out bulb. I replaced the bulb, turned off the map light and the door lights stopped working. Turned the map light back on and the door lights worked again. I was losing the ground to the door switches when the map light was off.

Here is the fix I came up with and the door handle lights and map light works as it should. Any thoughts? Can't understand why the original wiring doesn't work.

Facebook Facebook

Views: 50

Reply to This

Replies to This Discussion

If I remember correctly, the stock door switches have 3 terminals. 1 grounds the front interior lights, 1 grounds the rear interior lights, and 1 grounds the map light when the door is open. If you don't have 3 terminal switches or any terminals are tied together, it will provide a ground to other lights when you switch on the map light. Same thing for the rear light switch on the back of the front seat, if any terminals are tied together at the door switch, it will ground them too when the switch is on.

My 63 SDV only has two wires on the front door switch (a black/white and a black) and it only operates the front doors. The back doors work by themself. Did you see the colored wiring schematic that Jason put in the wiring section of the HELP section? 

Yeah, I've seen that wiring diagram. It's very helpful. Looks like the sedans are different but I'd say the problem is the same. The lights are either grounded by the door switch or the manual light switches. If your wiring is good & the door switches are functioning properly and making good bare metal contact, they will ground each wire connected to them. When your door lights only came on when the map light was on, that circuit was getting a ground through the map light switch, not the door switch. You can simply pull the wires off the door switches & ground them individually to test each circuit. The 12V at each wire is flowing through the bulbs so they will light up as the wire is grounded so it should not be a fuse-blowing direct short to ground. You would have to undo your mod to set things back to stock though.

RSS

Photos

  • Add Photos
  • View All

Forum

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 7 hours ago. 8 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Rainstorm out of nowhere!

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 1 Reply

After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue

Convertible bumper jack

Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 11 Replies

My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk.  Anyone have a picture of the item I should find?Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service