heater hose
I am replacing my heater hoses and was wondering if anyone has found a replacement for the 1479723. Its the 3/4" hose that goes from the heater core to the pipe running under the intake. Thanks
Replies to This Discussion
-
Permalink Reply by Larry Rees on
-
This is for a 64 Deville
-
-
I have tried to use a hunk of 3/4" off the roll but it starts to kink when bent in the small area. The hose that I removed was molded. It had the mold close enough to work but no part number left on it. The original part number 1479673 is no long any good but was looking for a conversion to a newer part number of a hose that is close enough to work without kinking.
-
-
Thanks good advice
-
Permalink Reply by Jason Edge on
-
Anyone have a good replacment # for Larry? I have replacement #'s for all the other hoses but would like to have a couple for this one. So, if you have a replacement # give us a shout. (Yes, I know we can all march to the auto store and have some one match one up, but we are looking for someone that has made that trek and id'ed a good replacement hose.)
-
Permalink Reply by David Thomas on
-
I us NAPA .75 inch 90 degree hose from the heater core to under manifold pipe. I think the part number is 9816. I trimmed the excess to fit. I use their 90 dgree .625 inch hose for the thermostat nipple to valve and from the valve to the heater core. Also trimmed to fit.
-
-
thanks
Members
Forum
Dino Radiator Leak - Time to Recore!
Started by Jason Edge in General Discussion. Last reply by Bill Wolf on Friday. 36 Replies 0 Likes
I had brought up the topic of radiator leaks as a discussion topic for our Chapter Zoom meet-up this past Sunday and thought I would share on our website for everyone and probably do a more formal…Continue
front seat crest
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Friday. 2 Replies 0 Likes
Original seats had a crest on the center arm rest. Does anybody know where I could embose a crest in new material for a reupolstry?Continue
64 Replacing dash illumination lights-how much has to come out to get to all of them?
Started by Norman Silverman in General Discussion. Last reply by Norman Silverman on Thursday. 11 Replies 0 Likes
Hello AllI have taken off my dash top and started replacing dash bulbs with LED's for greater visibility. Some questions:1) To replace the Gauge bulb it looks like easier access is had by removing…Continue
Correct whitewalls
Started by Richard Stanley in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Wednesday. 3 Replies 0 Likes
I just replaced my tires from Diamondback (I had bad results in the past from Coker). It was the second time, due to the age of the tires. About 18 years ago Diamondback made custom whitewalls…Continue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
