Im into removing door panel for water barrier and tge dand maual vent handle will not budge. I dnt see any screw holding it on the threaded stem, and other than forcibly prying off, which hasnt fared well either, i dnt know what to do and dnt wat to break the plastick handle, nor did i see any direct book instructions. Am i missing something?
Tags:
Check the shop manual, it should state how to remove the handle
I call myself reading it. In the body section under doors, guess i missed it. I hv since found an old article on the site about a spatula tool. Found one at store, will try it
Harbor Freight $6.99 for the set, use tool on right for vent handle.
i found one at oreilly,
i found a you tube video, guy used this tool on 60s GM windows,, he slid it over the handle, and it worked in about 1 second,, mine,, however did not, i saw the clip he was pushing down in his video, but apparently, the clip in mine had gotten stuck or somehow turned, long story short, after wedging pushing twisting prying for 4 hours, it came off..i could see where the clip had gotten stuck, i was almost at he point of cutting off as it simply would not move and pushing and pulling that clip was not working, finally, caught it with vise grips needle nose and pulled it out.. hand came off,, real pain in the azz.. ,, got the paper off, wire brushed the bottom of the inside of door, vacuumed it out, and paint with a good coat of rust in hibitor on the inside bottom.. just surfrace rust mostly,, but, got it out and re sprayed,
not in any hurry to do other side after all that,,
Old cars are definitely a labor of love. I find that beer and classic rock helps keep the calm in my garage.
The good news is that re-installing them is easy. Just put the clip back on the handle into the groove it came out of, and push the handle back onto the shaft until the clip clicks back into place. Good luck on the other side!
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Kurt 18 hours ago. 1 Reply 0 Likes
My front door handle lights would not go on when I opened the doors. Bulbs were good and had power to them. Was not getting a ground. The door switch was corroded and wasn't making contact when the…Continue
Started by Bill Wolf in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf yesterday. 2 Replies 0 Likes
I had to replace the heater core in my 63 SDV, so I decided to replace all the dash lights with LED's. and replaced all the vacuum lines. While I was in there, I added a light to the headlight switch…Continue
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Robert Alan Shannon on Tuesday. 9 Replies 0 Likes
I’m starting the complete rear suspension update/upgrade-new springs and shocks,replacing spherical joint and bushings on yoke and control links! Just wondering if there are any tips to help with the…Continue
Started by Mark Geertsma in 1963/64 Cadillac Specific Discussion. Last reply by Russ Austin on Tuesday. 4 Replies 0 Likes
I’m struggling with my TV rod adjustment. I’ve been trying to adjust it as per shop manual, but it’s still not OK. When cold, it shifts smoothly through all four gears, when hot, it hesitates (lots…Continue
Tags: adjustment, rod, TV
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments 1 Like
While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?
May 18, 2025 from 8pm to 9:30pm – Zoom
0 Comments 0 Likes
© 2025 Created by Jason Edge.
Powered by