Last fall I replaced my rear yoke and trailing arm bushings . Now with 410 miles on them the large
rear trailing arm bushings are done . I contacted Rare Parts the maker and they were defensive and
wanted me to purchase new ones and if sent the old ones back they, upon inspection would reimburse the original seller (Old Parts) a seller on ebay. Seemed like a lot of hoops to jump through so I inquired at all the
known Cadillac Suppliers and it seems the Rare Parts is the only maker of the RP15606 bushings . Further
internet searches found this is a common problem. This has led to Dan McNarry and Russ Austin heading up making replacement arms with high tech bushings that do not distort and last. Rare Parts needs to retool and use rubber that will last . In the mean time DO NOT purchase trailing arm bushings from them with the
expectation they will last as I assure you they will fail quickly
Tags:
I saw the post. I don’t need control links or bushings, but if I did I would check with someone like Steele that is well known for revulcanizing rubber mounts and see if they can work with sleeve bushings? I don’t know but does not hurt to ask and unlike trying to match up a metric size bushing, you will probably get a quick yes or no answer. Let me know what you find out.
Sounds good, Tony. Sort of thought they might be able to do something. So, if Jeff, Doug or someone wants to send them their control link with bad bushing they may have a better solution. The only thing I would question is why couldn't someone just send the old bushing?
I am sure there may be other areas where someone like Steele could fill a void where there are no other options.
Just to add, I have no knowledge of the availability of the upper control yoke bushings or the extent to their reliability. If I needed one, I would use google, and poll the troops here on the reliability of sourced bushings. If they were also crap material I would then pursue someone like steel to install new quality rubber. Again, a great project for you guys with "bushing issues"!
Caddy Daddy bushings are made by Rare Parts, that's were I ordered mine from.
I did not replace the yoke bushings, just control arms, as I stated earlier they are failing after 600 miles.
I am surprised because Rare Parts has a good reputation for producing quality parts.
Those large diameter rear bushings have to bear the weight of the whole car, they are obviously using a compound that is not dense enough to survive under this load.
Who makes the control link bushings, etc for Rubber the Right Way. For kicks and grins I decided to google 1964 Cadillac Control Link bushings and they were the 1st ones that popped up. I don't recall their name on this thread. Click Here to check them out.
Mark, that is why I asked "Who makes the control link bushings, etc for Rubber the Right Way?" The few times I have ordered from RTRW they came in Steele Rubber bags. I would assume they come from the same "crap" suppliers but I do not know that for a fact and is why I asked the question.
Just to add, I was surprised that the RTRW link had zero customer reviews. I would think if this is such a wide spread phenomenon people would be eager give their feedback.
One final thought, I was reading the installation of the control link bushings per shop manual and it said to torque the bolts to 60 ft lbs. For a large bolt this would be easy to exceed and wonder if those that have had issues have followed the torque specs. I would think there needs to be some allowance for the bushing to turn inside the link as the car flexes up and down. I wonder if over tightening these would force the bushing to lock in place causing the rubber inside to more rapidly tear apart for the circular stress as the control link flexes with the car? Just thinking aloud... but regardless I would torque to spec when installing.
I installed per the manual, with a torque wrench, tightening bolts only after car is off jacks and setting on the ground.
Old bushings were removed by removing center rubber section (drilling) then cut a groove in the shell with a hacksaw blade, then collapse shell with hammer and punch and remove from link.
New bushings were pressed in with a ball joint press, no force exerted on the rubber part of bushing or bolt sleeve, just on the shoulder flange of bushing. Spacers were used in link to prevent collapsing and distortion while using press.
These original links are rather light weight and are the flimsiest part of this cars suspension and great care must be taken to not damage them during bushing replacement.
I have both 63 and 64 style control links in VG condition for $55. If you are a CLC 1963/64 Cadillac Chapter Member, the price is $45 each. Some have decent used bushings, of course nothing like new, but Ok to use. If someone needs the control link(s) email me at jasonedge@nc.rr.com. If someone comes up with a good final solution I would definitely post to our Help Page. For me I have less than zero time to take on any additional projects, and if I did ... control link bushings would be way down my personal list. :-)
Travis J. Hensley Online
Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Patrick Westphal yesterday. 2 Replies 0 Likes
So I have been having problems with my brake lights. At first I thought it was both sides and turns out it is only the drivers side. Also, I thought the blinker worked and it didn’t and turned out…Continue
Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 11 Replies 0 Likes
Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue
Started by Nile Bolen in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 4 Replies 0 Likes
I checked the Help page and did a search on the site but didn't see any subjects on steering play/slack. Since I had someone complete a front end rebuild (Kanter kit, all the control arm bushings,…Continue
Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Vogler on Monday. 12 Replies 0 Likes
Late in the evenings, I wonder about things I will probably never do as I am not that crazy. However, I know someone out there has tried it or wanted it bad enough they have done it. My 64 Fltwd did…Continue
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinuePosted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
© 2025 Created by Jason Edge.
Powered by