Valve stem seals for 429?
Hello!
I am rebuilding 429 for 64 DeVille and got Felpro head gasket kit including valve stem seals. Is it recommended to install those even though they are not originally used? O-rings will be installed of course.
thanks in advance!
- Attachments:
Replies to This Discussion
-
Permalink Reply by 24ro8f5mbs2jc on
-
Hi Matti,
Yes its recommended. If you are able to read Swedish you can get additional information from TA Motor (best Company for Cadillac parts in Sweden).
-
Permalink Reply by Matti Roth on
-
Tack Anders! Jag har redan köpt ganska mycket från TA.
-
-
These kids today, I don't understand a word they say!
-
-
Thanks!
I am rebuilding it all by myself, with shop manual and other instructions. I have all the time in the world to get it right.
I am using original cam, crank, pistons, lifters, push rods, block, heads, valves, rocker arms. I need to replace 3 valves and 4 rocker arms only. Plus oil pump gears. New rings of course. Do I still need to do the break in run?
-
-
My concern is if the valve stem seals stay in the valve guides because they were not there originally. Are those 429 valve guides designed to keep stem seals in place?
If seals get loose they could create problems under rocker cover. I wonder if anyone in this group has added them.
Members
Forum
Convertible bumper jack
Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 1 hour ago. 1 Reply 0 Likes
My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk. Anyone have a picture of the item I should find?Continue
Wanted Cadillac Lasalle 2 inch Windshield Decal Sticker
Started by Doug Scarrow in Wanted to Buy. Last reply by Dennis P. DiBari on Saturday. 3 Replies 0 Likes
for close to 20 years I have had a lovely Club Decal on my windshield now I wish to replace the windshield and would love to buy a decal if any one has one available See attached photosContinue
Back to the 50’s
Started by Jordan Johansen-Moe in 1963/64 Cadillac Specific Discussion. Last reply by Jordan Johansen-Moe on Tuesday. 2 Replies 0 Likes
Is anyone here planning on going to the Back to the 50’s car show in Minnesota?
where to find 1963 Cadillac Plastic Door Pin Anchors
Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge Jun 15. 2 Replies 0 Likes
Hi allwhere can I find these - 1963 Cadillac Plastic Door Pin Anchors. Mine are from1963 and a little tiredThanksContinue
Blog Posts
1963 RHS A/C kick panel - photos needed
Posted by SK on June 2, 2025 at 2:20pm 2 Comments 0 Likes
Could someone post front and back photos of the 1963 right-hand kick panel with A/C?
My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.
Many thanks,
-Samu
Edelbrock Carb Block off Plates
Posted by Chase on March 12, 2025 at 2:05pm 14 Comments 1 Like
Hey guys,
I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…
ContinueNew old stock seat material
Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments 0 Likes
I bought this seat material thinking that it’s…
Events
Videos
© 2025 Created by Jason Edge.
Powered by
