Controlled Differential Decal
Does anyone have a pic of where the approximate location should be for the differential decal inside the trunk ? There is a pic In one of Jason's posts but it is a close up and not too definitive Thanks !
Replies to This Discussion
-
Permalink Reply by Tony and Ginny 429 on
-
You will have a tag on the differencial ( ham ) ,under the car
Do not think there is anything in the trunk ,myself
-
Permalink Reply by Jason Edge on
-
Marty I added better pictures on the Rear End/Differential thread at this link: http://6364cadillac.ning.com/profiles/blogs/differentials
Note, That I have pictures of 3 1964's with the Controlled and they are in the same location as posted in the link and on my car. I did find a 63 with limited slip and it was in the same relative location, but on the left side, so perhaps 63's was on the LH side. I know even on the 64's they are in the same relative spot but have seen them up or down an inch or two. Either way no one would knock any points off at GN judging regardless or side. I will dig around my parts car pictures some more.
-
Permalink Reply by Marty Smith on
-
Thanks Jason , I wasn't that concerned abut the judging points I was more concerned of you seeing it in the wrong place and asking why I didn't ask you where it went : ).
Photos
Members
Forum
Whoa there, you want how much??
Started by Robert Gonzalez in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 6 hours ago. 4 Replies 0 Likes
Ok, I’ve been on here for almost a decade. I KNOW we covet our cars and have always tried selling them at premium prices. But the bottom line, our cars rarely fetched prices over a covair. The…Continue
429 restoration
Started by Matti Roth in Restoration Discussion. Last reply by Matti Roth 7 hours ago. 7 Replies 0 Likes
Hello, and thanks for adding to group!I am restoring 1964 429 engine which I bought as dismantled. It is said to be smoking in driving and has been stored as parts for a year. It is most probably…Continue
Tags: #429
Free- 64 lower bumper bucket - Passenger side
Started by Michael Buonaccorso in For Sale. Last reply by Michael Buonaccorso yesterday. 2 Replies 0 Likes
This is in rough shape. Not only is there rust in the usual places but it is also bent. I replaced this piece on my car after an accident, but since this is a hard to come by piece, I figured someone…Continue
1964 Cadillac parts for sale... northern cali
Started by Jason in For Sale. Last reply by Jeremy on Friday. 1 Reply 0 Likes
Bill Hirsch cast iron gray exhaust and manifold paint (1 can) $20Bill hirsch Cadillac dark blue engine enamel high temp high gloss (2 cans) $40Convertible top latchValve coversHeadlight bezelRadioGas…Continue
Tags: Parts
Blog Posts
Rumble Sound at 55-60 mph
Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments 0 Likes
64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…
Continue1963 series 62 convertible transmission issue
Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment 0 Likes
Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…
ContinueNew vehicle in the club
Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment 0 Likes
I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha. …
Torque converter grab when idling in Drive
Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments 0 Likes
Hi Everyone, been quite a while since i have been on here.
I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.
With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.
I've had the car dyno tuned and…
ContinueEvents
© 2021 Created by Jason Edge.
Powered by
