Does anyone have a pic of where the approximate location should be for the differential decal inside the trunk ?   There is a pic In one of Jason's posts but it is a close up and not too definitive  Thanks  !

Views: 135

Reply to This

Replies to This Discussion

You will have a tag on the differencial ( ham ) ,under the car
Do not think there is anything in the trunk ,myself

Marty I added better pictures on the Rear End/Differential thread at this link: http://6364cadillac.ning.com/profiles/blogs/differentials

Note, That I have pictures of 3 1964's with the Controlled and they are in the same location as posted in the link and on my car. I did find a 63 with limited slip and it was in the same relative location, but on the left side, so perhaps 63's was on the LH side. I know even on the 64's they are in the same relative spot but have seen them up or down an inch or two. Either way no one would knock any points off at GN judging regardless or side. I will dig around my parts car pictures some more. 

   Thanks Jason , I wasn't that concerned abut the judging points I was more concerned of you seeing it in the wrong place and asking why I didn't ask you where it went : ).  

RSS

Photos

  • Add Photos
  • View All

Forum

You Know You Are Into Some Serious Car Doctor When You Have to Get the Ice Out!

Started by Jason Edge in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 4 hours ago. 14 Replies

You know you are into some serious car doctoring when you have to get the ice packs out. More to come on my 64 Coupe de Ville resuscitation in the next 1963/64 Cadillac Chapter Newsletter!  Mades…Continue

Unknown part, maybe the last one?

Started by Matti Roth in Restoration Discussion. Last reply by Jason Edge 4 hours ago. 1 Reply

Hithanks to great help from chapter members I am getting my 64 Deville ready, slowly but surely.There is only one part still unclear, or actually three bolts and nuts. They are clearly different from…Continue

Leaky Windshield

Started by Tom Bahner in General Discussion. Last reply by Tom Bahner 6 hours ago. 4 Replies

Hey all, has anyone had their windshield removed and resealed successfully. I'm pretty skittish about having someone mess with my perfectly good glass knowing that these cars are a little different…Continue

1964 THM Tilt Neutral Safety Switch

Started by Charles Fares in For Sale 20 hours ago. 0 Replies

For Sale:Excellent used neutral safety switch for 1964 with THM and tilt steering.  Part number 1993653, or short number "653".  Send me an e-mail: faresmcmthelix@msn.com.Charles FaresLa Mesa,…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service