I recently disassembled the right door of my '63 convertible to do a bunch of maintenance and restoration on several of its components. The door panel had not been particularity tight to the door, and I was not sure of the best way to re-assemble it with the nails/pins that hold the two sides of the panel to the door. I knew I could just use small nails, but it seemed these were not a great option. I did some searching, and the only alternative I found were the door clips show below, listed on eBay. I gave them a shot and they worked great.  (Plus it is only $14,19 for a set of 10 clips which does one door). I've ordered another set for my other door.

I have no connection to the seller, I'm just passing along the info in case others are facing a similar re-assembly challenge.

https://www.ebay.com/itm/192553041159

I think they were actually intended to clip over the thicker fiber/cardboard panel of the door panel, but that would have required me to make more adjustments to the vinyl covering than I wanted to make. Instead, I clipped them to the steel frame that runs around the panel. Everything lined up fine this way, so maybe that is how it is intended to be done. Here is how I did it:

1. I could find all the old nail holes (where the welds broke) or welds in the steel edging from the original nails and I marked their location in pencil on the inside of the door panel

2. I bent the clip part of the faster (just with my fingers) to create a narrower slot with about a 1/16" to 1/8" gap

3. I slid the faster over the steel edging at the pencil marks. The solid side of the clip faces the center of the door panel and the open side of the clip faces the edges of the panel. The pencil marks give you the up/down alignment on the door panel, and you have about 1/2" of up and down tolerance because the slots the nails go into on the door are about that length. For a few fasteners, I needed to make small cuts in the clips or in the door panel vinyl to get them to fit onto the steel frame well. These adjustments were easy to figure out and simple to do. I just cut the clips or vinyl with diagonal pliers.

4. Most mounted clips were plenty tight on the steel of the door panel, but I squeezed a few tighter just using a pair of pliers.

5.  I slipped the top of the panel over the top of the door and then just pushed the panel in top to bottom. I had two slide a few clips up or down a small amount, but this was also easy. The nail part is a ring-shank type nail, so they hold securely.

Before re-assembly, I took this picture of the inside of the door panel with the clips mounted. You can see the clips and pencil marks along the side edges of the door (click on the picture to go to full size). - Now I wish I had snapped a close up! The two clips near the top of the picture (which is the bottom of the door) and those on the right side of the picture are reasonably visible in the full size pict.

Facebook Facebook

Views: 593

Reply to This

Replies to This Discussion

Karl, this is great info. the original nails were ring shank type nails as seen in the male end part of your fasterners. I would how they look from the front and back and basically how they attach since the original nails just pushed straight thru the metal ridge and into the plastic insert in the door. These look like they would just press back into the blastic inserts but am having a har time picturing how the U shaped "head" attached to the door panel without being exposed?

Thanks for the tips - Fortunately I did all of this except the hinge grease, which I can do without taking things apart. Any suggested grease - If not I'll likely just use a lithium grease

Karl, this is really fantastic & helpful info and the way you just clip on the steel frame makes perfect sense! I hope you don't mind but I moved your details into the main post at top so it doesn't scroll out of site if we get a lot of replies. I also added a link and gave you credit on our Help Page under Door Panel Clips. I would also like to include in our next newsletter in the Tech Tips section. 

I'm always happy when I can contribute anything back to this group as I've learned a ton from other members here - letting me enjoy making basic fixes to my car and saving me some $ too!

ps. I just ordered 2 sets!

RSS

Photos

  • Add Photos
  • View All

Forum

Gump(Pat Westphal) you’re a gosh darn genius!

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Patrick Westphal on Friday. 2 Replies

So I have been having problems with my brake lights. At first I thought it was both sides and turns out it is only the drivers side. Also, I thought the blinker worked and it didn’t and turned out…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari Jul 22. 11 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Steering slack/play

Started by Nile Bolen in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari Jul 21. 4 Replies

I checked the Help page and did a search on the site but didn't see any subjects on steering play/slack.  Since I had someone complete a front end rebuild (Kanter kit, all the control arm bushings,…Continue

Tags: box, play, steering

Add cruise control/Aftermarket Cruise control

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Vogler Jul 21. 12 Replies

Late in the evenings, I wonder about things I will probably never do as I am not that crazy. However, I know someone out there has tried it or wanted it bad enough they have done it. My 64 Fltwd did…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service