Thanks to Jason's expert advice, I was able to remove the fender trim on my 63 de Ville without removing the fender. Pics contain the locations of the 3/8 in nuts and how to access them. My clips were trashed so I ordered 10 from Jason. He has the new once with nylon nuts. 

Facebook Facebook

Views: 214

Attachments:

Reply to This

Replies to This Discussion

Wow! Those are great Visuals.  We might use this for a future Tech Tip Series on removing trim.

If you don't mind I am going to insert here in the reply to see all at once:

Forgot to mention removing the front wheel to easily access the wheel well bolts. I put the wheel back on to lower the lift and roll it backwards to get the door fully open to access the hinge panel.

And to do a little self-promotion, here is a picture of the medium sized trim fasteners with bonded washer and nylon lock washer, used on front fender, rear qtr, and inner door section (of you want to replaced that snap on inserts). I sell these for $3 each ($2.25 after Chapter Discount).

Jason,

     Keep me in mind for that passenger side trim for my 64 Series 62.  I had it off in the winter and want to replace it if you come across one.  Pretty sure you have me on the wait list.  I have all the access points ready; just need the trim.

Thanks,

Dennis DiBari

are these clips used for the center three holes of the door molding/

They can be, but is not factory and is one of 3 attachment methods I recommend. I could go on but will repeat myself. See my detailed reply on your Body side molding install help needed thread.

RSS

Photos

  • Add Photos
  • View All

Forum

Gump(Pat Westphal) you’re a gosh darn genius!

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Patrick Westphal on Friday. 2 Replies

So I have been having problems with my brake lights. At first I thought it was both sides and turns out it is only the drivers side. Also, I thought the blinker worked and it didn’t and turned out…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 11 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Steering slack/play

Started by Nile Bolen in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari Jul 21. 4 Replies

I checked the Help page and did a search on the site but didn't see any subjects on steering play/slack.  Since I had someone complete a front end rebuild (Kanter kit, all the control arm bushings,…Continue

Tags: box, play, steering

Add cruise control/Aftermarket Cruise control

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Vogler Jul 21. 12 Replies

Late in the evenings, I wonder about things I will probably never do as I am not that crazy. However, I know someone out there has tried it or wanted it bad enough they have done it. My 64 Fltwd did…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service