Had my double surgery on left arm March 4 on wrist and elbow to address Cubital Tunnel Syndrome and so far so good. Basically the open me up at these two locations and move the Ulner nerve around to decompress it.   Unlike Carpel Tunnel, which affects thumb and index finger, this affects outer fingers on the pinky side. When It is bad like I had it you lose feeling and feels like your hand is always asleep in that side.  Anyway, it looked pretty wild 2 days ago when I got the soft cast off but now have to wear an arm brace for 4 weeks and do lots of stretching exercises. There has really been no paint, just soreness.   After the first couple of days I have been pretty active but the case made typing and even thumbing on the cell phone tough. I already have some feeling back on the affected fingers and can now type away much better than even before. They removed stitches today and will take several months for the nerve to fully heal itself. It may never be 100% but I will take 75% over 0% any time. 

During my down time I have been doing what I can with my right hand. Helping my wife sort the cadmium plated fasteners has been one of my activities. I even did what i said I wasn't going to do, sort in the new dining room on the big table. Just made it easier for me! 

Here is a picture of my sorting office. You will notice the presort buckets #8, #10, 1/4", 5/16", etc.  Here I am sorting larger washers.

I will often go after type of washers as a group. That is I will do flat washers, split lock washers, other lock washer types, bolts, nuts as separate large groups.  The really small stuff like the #6, #8, #10 screws and nuts may end up as separate groups done at the end as it is tedious! 

Each group will then get subdivided.  With bolts for Example:
I will usually 1st group by the bolt diameter, then further breakdown by the head type (eg. reg hex head, raised ridge head, reg flange head, serrated flange head, hex head with external lock washer, etc..)  After, that I will group by bolt length, then head stampings.

That's been my process since day 1 and seems to work for me.

Facebook Facebook

Views: 58

Reply to This

Replies to This Discussion

Hey Righty, I was wondering how your recovery was coming along! Sounds like you are doing well and getting something done also!

Hey Jason , Glad to here the surgery went well !    The Neurologist at the Mayo clinic told me to take vitamin B-12 to help my damaged nerves recover, nerves like B-12 nerves take the longest to recover after surgery  or being damaged they grow the slowest they told me . How do you like being right handed??

Chris, I hate being right handed. Ha Ha! I pretty much stopped drinking coffee 15 years ago and do these ZipFizz energy drinks at least twice a day with tons of B-12 and a lot of other vitamins.  Glad to hear that will help with the nerve repair! Got a long way to go but think it will be worth in in the long run!

Jason,

     Take care of yourself and let your left hand heal.   Just give it some time.

Dennis DiBari

RSS

Photos

  • Add Photos
  • View All

Forum

Dino Radiator Leak - Time to Recore!

Started by Jason Edge in General Discussion. Last reply by Bill Wolf yesterday. 36 Replies

I had brought up the topic of radiator leaks as a discussion topic for our Chapter Zoom meet-up this past Sunday and thought I would share on our website for everyone and probably do a more formal…Continue

front seat crest

Started by Frank Murch in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf yesterday. 2 Replies

Original seats had a crest on the center arm rest.  Does anybody know where I could embose a crest in new material for a reupolstry?Continue

64 Replacing dash illumination lights-how much has to come out to get to all of them?

Started by Norman Silverman in General Discussion. Last reply by Norman Silverman on Thursday. 11 Replies

Hello AllI have taken off my dash top and started replacing dash bulbs with LED's for greater visibility. Some questions:1) To replace the Gauge bulb it looks like easier access is had by removing…Continue

Correct whitewalls

Started by Richard Stanley in 1963/64 Cadillac Specific Discussion. Last reply by Bill Wolf on Wednesday. 3 Replies

 I just replaced my tires from Diamondback (I had bad results in the past from Coker).  It was the second time, due to the age of the tires.  About 18 years ago Diamondback made custom whitewalls…Continue

Tags: width, whitewall, correct

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service