A few questions on the resistor wire, what color is it in the pic? The yellow/blue or black? And connecting to the ACC on the fuse box seems easiest way to go with the new switched wire, but where can I get a connector for the ACC?

Views: 300


Reply to This

Replies to This Discussion

Hi Dave,

     I have never seen a fuel line twisted like that.  Pretty sure the gas flow is quite restricted.  Any chance to run a new fuel line from the fuel pump to the carb.?

Dennis DiBari


     If you get new fuel line and a good flaring kit, you can run a new line to the carburetor.  You can use the fittings you already have and put them on the line before you flare both ends.  The gas flow will be correct.


Tabs in red are  not interlocked. If you want a better fuel line I have a nice original fuel filter to Carter AFB carb line I just pulled from the last parts car. Price is $25, which drops to $18.75 with Chapter Discount and can ship for $10 for a final total of $28.75. Shoot me an email if interested.

Dave, Have you been able to get your ignition system operating properly?  I think that you are wired into the wrong circuit for 12 volt power.  I would be glad to get on a call with you to discuss it if you would like that.  

Pat, that would be great as I will take any and all help getting this beast back in running mode! I sent a friend request, then i can send you my number. 

I wanted give an update on pertronix 3 installation. 
It is now working but it was not a straight line install and then running!  Originally I used the ACC for the switched 12 volt with no success. Then I cleaned up the fuse holders for the ACC and got 12 volts to the end of the wire. But it still wouldnt start and in stepped Pat Westphal!! He suggested tapping i to an ‘ignition’ line, either the pink wire that the resistor wire is connected to or using the tan/white wire that runs into the wiper motor in the engine bay. It is definitely an easier access point, so i used it. 
In the meantime, i was waiting for a fuel line from Jason Edge from filter to carb. Of course, during the install i cross thread into the filter-“&$:&!?$& were the exact words used! Luckily, it was the female connector on the filter that cross threaded and you tube had a nice fix and it worked. So installed all fuel lines, and fired it up and started right up!! 
Again big shout out to Pat and Jason for all the help and willingness to share their knowledge!



  • Add Photos
  • View All


Speedometer Drive Gear

Started by John Cason Fudala in 1963/64 Cadillac Specific Discussion 5 hours ago. 0 Replies

When driving my 63 the speedometer reading is about 5 to 7 faster than what I am actually traveling. I have not removed the gear to count the number of teeth it has. The rear axle ratio is 3.21. Does…Continue

Fender Trim Removal

Started by Kevin Wray in Restoration Discussion. Last reply by Kevin Wray yesterday. 4 Replies

Thanks to Jason's expert advice, I was able to remove the fender trim on my 63 de Ville without removing the fender. Pics contain the locations of the 3/8 in nuts and how to access them. My clips…Continue

Tags: removal, trim

Congratulations Logan Robb!

Started by Jason Edge in General Discussion on Saturday. 0 Replies

A big congratulations to CLC member Logan Robb for his cover feature in the June 2024 CLC Self-Starter magazine with his new bride Annie and 1964 Fleetwood 60 Special! Well done!!…Continue

New Correct 1963-64 Cadillac Spring Ring Battery Cable Set - $150 for Chapter Members

Started by Jason Edge in For Sale. Last reply by Jason Edge on Saturday. 1 Reply

See Many More Pictures On My Facebook Parts Page at this Photo Album Link…Continue

Tags: cables, battery, rong, spring

Blog Posts

Loud air moving sound within carb with cleaner removed

Posted by Dave Fehrle on March 23, 2024 at 3:23pm 8 Comments

While checking my Carter carb with engine running, I took the air cleaner off and there was a very loud hissing sound of air. I placed a piece of paper over the carb and it didn’t move up or down, is this normal?

Vintage Air AC

Posted by Chase on March 21, 2024 at 5:55am 0 Comments

Hey everyone, has anybody done a Vintage Air AC/Heat setup in their car? I want to bypass the old vacuum setup and go with a Vintage Air Gen 2 model. Before I get started, does anyone have any experience with this? (Which model to go with, do’s and dont’s, etc.) It looks pretty involved. Any and all info/pics would be greatly appreciated. Thanks!

accumulator dryer

Posted by CHRIS CARLSON on December 6, 2023 at 10:54am 0 Comments

Who rebuilds original AC  accumulator dryers for 1964 Cadillac? I have been on Classic auto air in Tampa FL wait list for over a year ,  There is one on Old air products web site that looks very similar to the original # 21-4214A but states it fits 1962 Gm cars, The one recommended for a 1964 Cadillac is half the length 21-4215A    What  is everyone using ? I would prefer to be as original as possible. Thanks

'63 Eldorado trumpet horn + 2 standard horns restoration

Posted by Les Eastling on November 15, 2023 at 10:34am 1 Comment

My son, unbeknownst to me, had all three of the horns on our 1963 Eldorado completely restored. We had recently added the Eldorado trumpet horn to the two standard horns and the sound was not very good... we had heard good ones so we knew something was not right... but there was not much we could do to get better sound from the 3 horns. 

There is a restoration service called The Horn Works who my son…



  • Add Videos
  • View All

© 2024   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service