Hello!

I am rebuilding 429 for 64 DeVille and got Felpro head gasket kit including valve stem seals. Is it recommended to install those even though they are not originally used? O-rings will be installed of course.

thanks in advance!

Views: 58

Attachments:

Reply to This

Replies to This Discussion

Hi Matti,

Yes its recommended. If you are able to read Swedish you can get additional information from TA Motor (best Company for Cadillac parts in Sweden).

Tack Anders! Jag har redan köpt ganska mycket från TA.

These kids today, I don't understand a word they say!

Matti

Always best to use valve stem seals as they prevent oil being sucked into the cylinders between the valve stem and valve guides ( especially intake valves ) 

This is often done by a machine shop when refreshing the heads as all the valve springs must be removed to install the valve stem seals at the top of the valve guides 

The best valve stem seals I know are —PC Seals —as the top of the valve guide is cut by a machine shop to be installing those which are used in high performance race engines for there positive qualities 

Always be very sure to be installing your rocker arms correctly as some of the best professional engine building shops have installed them wrong on newly rebuilt engines preventing proper oil flow to the heads —-on the ever so important —First break in run to seat the new engines metal parts 

That first engine break in run will determine the condition of  the new engines performance and  longevity for the long haul so very important to get  that right  the first time 

Enjoy 

Thanks!

I am rebuilding it all by myself, with shop manual and other instructions. I have all the time in the world to get it right. 
I am using original cam, crank, pistons, lifters, push rods, block, heads, valves, rocker arms. I need to replace 3 valves and 4 rocker arms only. Plus oil pump gears.  New rings of course. Do I still need to do the break in run?

The break in run is the first 30 minutes the engine runs  for the first time to be polishing all metal to metal surfaces so that they form a smooth  shinny surface between those metals for the life of the engine 

Mostly it is about setting up the engine to fire up as quickly as is possible and then run the engine over 1000 RPMs for 30 minutes non stop and getting the engine to operating temp 

After that run up you will need to re-torque all bolts to  the engines manuals  specs 

Then removing any bugs that pop up like leaking hoses — etc 

A very important procedure fir engine longevity and very much required 

Enjoy 

My concern is if the valve stem seals stay in the valve guides because they were not there originally. Are those 429 valve guides designed to keep stem seals in place?
If seals get loose they could create problems under rocker cover. I wonder if anyone in this group has added them.

RSS

Photos

  • Add Photos
  • View All

Forum

Replacing Front Door Window Chrome Channel

Started by Michael Vogler in General Discussion 1 hour ago. 0 Replies

List Mates,My '64 De Ville Conv. front door window chrome trim needs to be replaced.  The chrome on both front door window his getting a little bit of pealing off.  I have the chrome replacement…Continue

Vacuum advance

Started by Thomas Yarri in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 15 hours ago. 1 Reply

Good afternoon to all my fellow Cadillac owners! I have a question about the vacuum advance on my car. The car is a 64 without a/c and a Rochester carburetor. I noticed that I have vacuum at the port…Continue

1963-1964 Convertible Parts

Started by Charles Fares in For Sale 21 hours ago. 0 Replies

1963-64 Convertible top switch with chrome bezel and mounting retainer clip, tested and working, nice chrome, $65. 1963-64 Convertible rubber A-pillar seals LH and RH pair (repops) $50 the pair.…Continue

Over heating

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 22 hours ago. 9 Replies

Hi, been doing the break in still. At about 450 miles.I hve noticed that when i go out, temp gets to between 1/4 and 1/2 on the gauge.  If i sit any period of time or dnt keep moving, it creeps…Continue

Blog Posts

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service