Russ Austin's Discussions (2,335)

Discussions Replied To (2112) Replies Latest Activity

"pressure is good to go."

Russ Austin replied Aug 6, 2014 to oil pressure

1 Aug 6, 2014
Reply by Russ Austin

"I run the Carter P60430 electric fuel pump on both of my cars, and have no complaint…"

Russ Austin replied Aug 6, 2014 to fuel pump psi

2 Aug 6, 2014
Reply by Russ Austin

"I do know that the Commercial Chassis is different. Not sure about the series 75.  T…"

Russ Austin replied Aug 3, 2014 to Passenger floor pan plus some

10 Dec 10, 2014
Reply by Shorty

"Jason and myself have parted out Limo's.  I recently parted out a 64. The 64 came wi…"

Russ Austin replied Aug 3, 2014 to 500 Swap into Commercial Chassis

14 Aug 3, 2014
Reply by Shorty

"I agree that the stock tranny will hold up for todays travels.  I did the math for m…"

Russ Austin replied Aug 3, 2014 to Transmission questions.

9 Aug 3, 2014
Reply by nic spruill

"Not sure what tranny you had in the 65 limo, but I have a 64 limo drive shaft.  The…"

Russ Austin replied Aug 2, 2014 to 500 Swap into Commercial Chassis

14 Aug 3, 2014
Reply by Shorty

"Were they working correctly before?  if they were not, I would guess that the wiper…"

Russ Austin replied Jul 26, 2014 to Wiper Motor will not "Park" wipers in correct Position.

13 Jul 30, 2014
Reply by Dan Benck

"Same with me, fresh out. Better get that starter brace, just as hard to find."

Russ Austin replied Jul 26, 2014 to Wanted to buy 64 deville transmission parts

6 Jul 30, 2014
Reply by Mark S Anderson

"30 over is just fine."

Russ Austin replied Jul 24, 2014 to 64' 429 engine rebuild

11 Jul 24, 2014
Reply by Russ Austin

"I use the 2 O-rings, small amount of blue or orange RTV, and the washer trick.  http…"

Russ Austin replied Jul 24, 2014 to Water pump riser

3 Jul 24, 2014
Reply by Todd Lentz

RSS

Photos

  • Add Photos
  • View All

Forum

Rear glass

Started by David Stapp in 1963/64 Cadillac Specific Discussion. Last reply by David Stapp 13 minutes ago. 10 Replies

anyone know of a company that makes the rear glass for our cars? I can’t seem to find any. 1964 4 door 4 window hard top.…Continue

Where can I buy resistance wire for my 1963?

Started by Tim Walterson in 1963/64 Cadillac Specific Discussion. Last reply by Tim Walterson 16 minutes ago. 4 Replies

Hello - just signed up for this forum - looks like a great resource!  I perused the posts and did some searches.  I see most of the posts related to my questions are about doing away with resistance…Continue

front engine pulley removal

Started by tom servas in 1963/64 Cadillac Specific Discussion. Last reply by tom servas 11 hours ago. 7 Replies

Am removing the front cover on our 64 engine with AC. Have all 6 bolts that hold the pulley onto the damper removed, can wiggle the pulley BUT it will not come fully off the damper, Is there…Continue

Blog Posts

Is there a separate Starter Relay, or does the Solenoid serve that purpose?

Posted by Norman Silverman on August 30, 2019 at 5:57pm 7 Comments

Hello All.

I will be replacing the starter solenoid tomorrow (actually my mechanic will do the work, I'll just supervise). In checking the FSM electrical schematic and chapter verbiage, I don't see anything that looks like (or is referred to as) a starter Relay. It seems the Starter Solenoid serves the function and there's no separate relay. Right or Wrong?

If wrong, where…

Continue

Starter Solenoid replacement-how difficult? Where to buy?

Posted by Norman Silverman on August 20, 2019 at 8:24pm 8 Comments

Hello All.

I believe the starter solenoid has gone bad in my 64 DeVille. When I turn the key, often all I get is a click, then if I try a few times again the starter turns perfectly. All battery cables are on tight and the battery is good. So, I believe this problem is the solenoid. Where do I buy the right solenoid and is it necessary to remove the starter in order to swap it out? …

Continue

Frame Markings

Posted by Gene McIlroy on August 12, 2019 at 6:26pm 1 Comment

Just got my frame back from powder coating so thought I would post photos of the front and rear frame markings.…

Continue

Lining up the drive shaft

Posted by Dominic Salemi on August 12, 2019 at 5:47pm 2 Comments

Can anyone shed some light on how to position the complete drive shaft in the correct position? I want to make sure my drive shaft is installed properly.

Thanks

Dominic

Events

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service