Walt Timmerman's Discussions (26)

Discussions Replied To (21) Replies Latest Activity

"yes, that is explained by the date on it when I posted.  Thanks for the confirmation…"

Walt Timmerman replied May 28 to 63 4 door cadillac

19 May 28
Reply by Walt Timmerman

"It is"

Walt Timmerman replied May 26 to 63 4 door cadillac

19 May 28
Reply by Walt Timmerman

"might have it all. sent a email. about questions. "

Walt Timmerman replied May 21 to 63 4 door Cadillac

5 May 21
Reply by Walt Timmerman

"Saint Peter,mn not sure on miles. i'll have to look"

Walt Timmerman replied May 21 to 63 4 door cadillac

19 May 28
Reply by Walt Timmerman

"never heard it run. pulled it without trying to fire it. Previous owner said it ran…"

Walt Timmerman replied Mar 27 to 63 4 door Cadillac

5 May 21
Reply by Walt Timmerman

"Hood and front fenders are gone.  Steering wheels is also sold."

Walt Timmerman replied Mar 23 to 63 4 door Cadillac

5 May 21
Reply by Walt Timmerman

"I was just seeing if maybe someone had used something and where they may have gotten…"

Walt Timmerman replied Nov 20, 2020 to tubular a-arms

2 Nov 20, 2020
Reply by Walt Timmerman

"33,471 miles"

Walt Timmerman replied Nov 16, 2020 to 63 4 door cadillac

19 May 28
Reply by Walt Timmerman

"Minnesota, front end is gone already along with the hood and steering wheel. check i…"

Walt Timmerman replied Nov 16, 2020 to 63 4 door cadillac

19 May 28
Reply by Walt Timmerman

""

Walt Timmerman replied Nov 15, 2020 to 63 4 door cadillac

19 May 28
Reply by Walt Timmerman

RSS

Photos

  • Add Photos
  • View All

Forum

Neutral Switch issues

Started by Rob Shatsnider in Restoration Discussion. Last reply by Mark S Anderson 32 minutes ago. 1 Reply

On a 1964 60 Special with a tilt wheel, tubro trans and #653 neutral switch.  When I had the transmission done the switch got out of alignment.  Now the car will start in Park, but not in Neutral,…Continue

Tags: issues, Switch, Neutral

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by mark zimmerman 58 minutes ago. 9 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 2 hours ago. 19 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

Carpet install

Started by Pete Grodem in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 3 hours ago. 1 Reply

simple question, Does the carpet go under the seat mounts and bolted down with the seat? My original carpet was cut to go around the seat mounts looks like a hack job. Same with the steering column,…Continue

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service