64 THM Electric Kickdown switch connections: only two at linkage, or more at Tranny?

Hello all.

As I reported in a prior post, I got my car back from the shop and now have a part throttle kickdown. Great! However, either by coincidence or by oversight I now no longer have a Full throttle kickdown (which I used to have after I replaced the switch on the linkage). So, I checked the connections on the linkage and they appear to be good. What I am wondering is whether there are other electrical connectors at the transmission, which may have been disconnected during the repair and not re-attached. I don't have a lift so I cannot check (other than doing it the "Brooklyn way" by driving the car half way in to the street in the driveway and crawling under -which I will do if I have to. 

So, anybody know if there are other connections at the tranny? There does not appear to be a fuse on that line.

(Yes, I do plan to test the switch  with a test light but have not done that yet because it worked fine before I dropped the car off). 

Thanks

Norm

Views: 51

Reply to This

Replies to This Discussion

The white wire from kick down switch goes to transmission connector. Trace it back to transmission connector and make sure it is attached and no breaks in wire.

Thanks. Approximately where on the tranny does it connect? Near the Modulator or somewhere else.

See arrow below:

Noted with appreciation. 

I just always  love the pictures with circles and arrows for clarity 

Always reminds me of the song — Alice’s Restaurant 

Enjoy 

Occam's Razor rules the day: It was a bad kick down switch on the linkage. Shoulda checked it first but it was working just a week ago. 

Thanks for all responses, I learned something anyway.

Norm

RSS

Photos

  • Add Photos
  • View All

Forum

Neutral Switch issues

Started by Rob Shatsnider in Restoration Discussion 22 minutes ago. 0 Replies

On a 1964 60 Special with a tilt wheel, tubro trans and #653 neutral switch.  When I had the transmission done the switch got out of alignment.  Now the car will start in Park, but not in Neutral,…Continue

Tags: issues, Switch, Neutral

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 1 hour ago. 19 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

Carpet install

Started by Pete Grodem in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge 2 hours ago. 1 Reply

simple question, Does the carpet go under the seat mounts and bolted down with the seat? My original carpet was cut to go around the seat mounts looks like a hack job. Same with the steering column,…Continue

Classic Cadillac Parts For Sale - Misc Items

Started by Jason Edge in For Sale. Last reply by Jason Edge 2 hours ago. 247 Replies

I have posted a few Misc items over on my Classic Cadillac Parts Facebook page at…Continue

Tags: classic cadillac parts, classiccadillacparts

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service