I am in the middle of doing a carburetor update and I am planning on blocking out the middle exhaust ports on the in manifold as per Jason's instructions on doing this update.  I am going to install an Edelbrock 1406 carb with electric choke.  In the instructions Jason mentions that the intake manifold gaskets should be updated to the thicker kind in order to seal around the metal plate being added to block off the exhaust passage that goes through the intake manifold on the production set up.  Does any one have a place that I can order those type gaskets either online or at an auto parts store.  I am only finding either the same thin type gaskets that are already on the car and won't seal properly, or what looks to be a gasket made from rubber from a company called Fel-Pro, and I don't know if those will do the trick.  I know that I am not the first one to do this update so where can I get the proper gaskets from?  Any suggestions will be greatly appreciated.  

Facebook Facebook

Views: 136

Reply to This

Replies to This Discussion

Hey Pat ,

give me a call ,I’m in the middle of doing my carburetor project right now. I have some useful info for you .email me at schrym@aol.com I’ll  send you my number

 Thanks Ray. 

RSS

Photos

  • Add Photos
  • View All

Forum

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari 10 hours ago. 8 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Getting hot when going fast…

Started by Mack in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari yesterday. 6 Replies

So… I do have a few of 63 Coupes, all have same setup with carbs, Pertronix, shroud, new US Radiator radiators etc … but only one of them gets a bit hot when I am hauling faster than 60mph and car…Continue

Rainstorm out of nowhere!

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Monday. 1 Reply

After dinner last night, we went for a quick cruise as the weather was cooler and the sun set was looking really good!Out of nowhere, a pop up shower appeared overhead and down-poured as we were…Continue

Convertible bumper jack

Started by Alan Clark in 1963/64 Cadillac Specific Discussion. Last reply by Logan Robb on Monday. 11 Replies

My car lacks the mechanism or spring needed to hold the jack in the storage slot on the right side of the trunk.  Anyone have a picture of the item I should find?Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service