Hi all

here are some more parts from under the hood to identify

number 1 is two clamps

number 2: 2 bolts, different threads at each end

number 3 is bracket with cadillac blue paint

good luck!

Facebook Facebook

Views: 154

Attachments:

Reply to This

Replies to This Discussion

OK. I'll have a go. 1st Picture are the dehydrator (dryer) clamps taht hold it against the radiator support. You would also have 2 screw that go into two U nuts. Here is a pic:

2nd picture includes 2 of the 4 inner intake manifold fasteners sets. These 3/8" studs are 16 thread on one end and 24 thread on the top end where nut attached. Here is a picture:

3rd picture is the carburetor throttle return bracket and an outer intake manifold to cylinder head bolt. This attached at left rear of engine see picture below:

Thanks! Photos are great help. Pic 2: I found out that 2 studs are still in heads, and I found a nut for one of them. Two washers more were found as well so I have all 4 pcs. I found several bolts which could be used for the corners of intake manifold. There is no space for such big washers like with studs.

RSS

Photos

  • Add Photos
  • View All

Forum

Gump(Pat Westphal) you’re a gosh darn genius!

Started by Dave Fehrle in 1963/64 Cadillac Specific Discussion. Last reply by Patrick Westphal on Friday. 2 Replies

So I have been having problems with my brake lights. At first I thought it was both sides and turns out it is only the drivers side. Also, I thought the blinker worked and it didn’t and turned out…Continue

Front grill

Started by Phillip Hill in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari on Tuesday. 11 Replies

Hi everyone im currently restoring my my front grill due to some previous clown painting it with silver frost paint and doing a dodgy job I would like to know what parts of the grill are anodised.it…Continue

Steering slack/play

Started by Nile Bolen in 1963/64 Cadillac Specific Discussion. Last reply by Dennis P. DiBari Jul 21. 4 Replies

I checked the Help page and did a search on the site but didn't see any subjects on steering play/slack.  Since I had someone complete a front end rebuild (Kanter kit, all the control arm bushings,…Continue

Tags: box, play, steering

Add cruise control/Aftermarket Cruise control

Started by Logan Robb in 1963/64 Cadillac Specific Discussion. Last reply by Michael Vogler Jul 21. 12 Replies

Late in the evenings, I wonder about things I will probably never do as I am not that crazy. However, I know someone out there has tried it or wanted it bad enough they have done it. My 64 Fltwd did…Continue

Blog Posts

1963 RHS A/C kick panel - photos needed

Posted by SK on June 2, 2025 at 2:20pm 2 Comments

Could someone post front and back photos of the 1963 right-hand kick panel with A/C?

My car didn’t come with the original kick panels, so it's a bit of a mystery to me how I should cut the backing board and carpet to fit around the A/C.

Many thanks,

-Samu

Edelbrock Carb Block off Plates

Posted by Chase on March 12, 2025 at 2:05pm 14 Comments

Hey guys,

I have installed the same Edelbrock carb and have done everything the same as Jason’s carb and intake project. In the spring and summer months the car starts, runs and idles great! In the fall and winter months on a cold start, the car starts awful and wants to die until it warms up. I have to keep my foot on the throttle until it warms up or it will idle just terrible and try to die. Once it’s warm, it runs fantastic! Whats going on here? I was thinking of removing the…

Continue

'63 Tailfin Tales

Posted by Mark Mata on February 22, 2025 at 5:00pm 9 Comments

New old stock seat material

Posted by Ray Schick on August 22, 2024 at 6:25pm 2 Comments

I bought this seat material thinking that it’s…

Continue

Videos

  • Add Videos
  • View All

© 2025   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service