Tony and Ginny 429's Discussions (4,556)

Discussions Replied To (4424) Replies Latest Activity

"Where are you located ? Enjoy"

Tony and Ginny 429 replied on Saturday to Free 1964 parts before I throw them out

7 yesterday
Reply by Russ Austin

"This 1963 CDV is about as good as it gets regarding its restorations  attention to a…"

Tony and Ginny 429 replied on Friday to 1963-64 Authenticity Manual

7 on Friday
Reply by Kenneth M Karrer

"I know the two columns are  very different but not sure about the specific differenc…"

Tony and Ginny 429 replied on Friday to Very Hot Steering Column.

5 on Friday
Reply by Russ Austin

"I would be examining the signal switch wiring that is in the column below the steeri…"

Tony and Ginny 429 replied on Friday to Very Hot Steering Column.

5 on Friday
Reply by Russ Austin

"You most certainly have an electrical issue inside the column if you got a shock fro…"

Tony and Ginny 429 replied on Friday to Very Hot Steering Column.

5 on Friday
Reply by Russ Austin

"Karl  I use the  high heat wheel bearing grease myself on the door hinges Those larg…"

Tony and Ginny 429 replied on Friday to Door Panel Clips (Fastener Nails)

8 on Friday
Reply by Karl Schwarz

"A very good time to install a 4mil plastic liner ( Home Depot ) into the door skins…"

Tony and Ginny 429 replied on Thursday to Door Panel Clips (Fastener Nails)

8 on Friday
Reply by Karl Schwarz

"The correct size sheet metal screw into the plastic female bushing will work with ju…"

Tony and Ginny 429 replied on Thursday to Door Panel Clips (Fastener Nails)

8 on Friday
Reply by Karl Schwarz

"Kim Because the trans shifts off the TV rod in the 63 —attached to the carb I would…"

Tony and Ginny 429 replied on Tuesday to Edelbrock 1406 & 1411 Installation Summary

21 on Tuesday
Reply by Jason Edge

"Fun stuff to know  Enjoy "

Tony and Ginny 429 replied Jun 29 to 1963 & 1964 Cadillac Factory Installed Equipment Percentages

10 on Wednesday
Reply by Jason Edge

RSS

Photos

  • Add Photos
  • View All

Forum

Rear Wheel Bearings Replacement

Started by Dominic Salemi in 1963/64 Cadillac Specific Discussion 29 minutes ago. 0 Replies

HiNeed to replace my rear wheel bearing and seal on my 1964 Conv., does anyone know if its a big project and what I will need before I pull the shaft out? I also need to know the parts number and…Continue

Winter time cruise in Australia.

Started by Kevin Campbell in General Discussion. Last reply by Kevin Campbell 34 minutes ago. 4 Replies

The weather here in winter is great for a Cadillac cruise.Continue

looking for a 429 heat riser and cruise control unit

Started by Christian Doerk in Wanted to Buy. Last reply by Kurt 1 hour ago. 1 Reply

I am looking for a functioning heat riser valve and a cruise control for a 1964 Cadillac.In principle, the heat riser flap does not have to work. It is only important that the spacer / housing is not…Continue

Tags: exhaust, riser, heat, control, cruise

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 3 hours ago. 1 Reply

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

64 Power Servo vacuum leak

Posted by Kent Prows on June 27, 2020 at 4:02pm 0 Comments

I finally got around to fixing a leak in my heater core.  I decided to check to see if there were any other obvious issues while I had everything torn apart.  When I put a vacuum directly (bypassing the transducer) to the power servo it gets to about 10" and then slowly leaks back to zero.  The fan will not go to full and the mode door will not open completely.  I have read a couple of other posts that said they repaired the power servo leaks.  How?  Does anyone have one to sell?  I just…

Continue

63 Caddy Horn

Posted by Robert Alan Shannon on May 27, 2020 at 9:25am 9 Comments

 Just noticed a 1963  Caddy trumpet horn on Ebay. No part # given but some of his other items are 1963 specific, just throwin this out there, I have no connection to this listing .

Wiring connection help.

Posted by Jimmy Davis on May 24, 2020 at 9:15pm 2 Comments

Can someone help me figure where these connections go? I have a 64 60 special if it matters.…



Continue

Wood grain finally done.

Posted by Jimmy Davis on May 20, 2020 at 4:57pm 3 Comments

After years of wanting to, I finally redid my wood dash paneling on my 64 60s. Not too hard to do either.…

Continue

Videos

  • Add Videos
  • View All

© 2020   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service