JOHN V SCHILLACI's Discussions (18)

Discussions Replied To (17) Replies Latest Activity

"I'll assume the wheels are balanced and properly inflated and aligned. Could be shoc…"

JOHN V SCHILLACI replied Sep 10 to Front End Wheel Hop

8 Sep 11
Reply by Tony and Ginny 429

"Hello, Are you looking for a fixer upper or one  ready to roll?"

JOHN V SCHILLACI replied May 6 to Looking for feedback

21 May 11
Reply by Jason Edge

"Hello, Thank you for your advice. The tube is cracked/broken.  Do you think that a s…"

JOHN V SCHILLACI replied Nov 25, 2020 to Dipstick tube

3 Nov 25, 2020
Reply by Jason Edge

"Hello, I have a used on that i'm sure would need machined as a last resort for you.…"

JOHN V SCHILLACI replied Nov 25, 2020 to 1964 429 timing cover needed

2 Nov 25, 2020
Reply by JOHN V SCHILLACI

""

JOHN V SCHILLACI replied May 2, 2020 to deville 64 convertible

8 May 2, 2020
Reply by JOHN V SCHILLACI

""

JOHN V SCHILLACI replied May 2, 2020 to deville 64 convertible

8 May 2, 2020
Reply by JOHN V SCHILLACI

"Hello, I have a 64 Deville convertible. I have owned it since 1976. It has A/C, powe…"

JOHN V SCHILLACI replied May 2, 2020 to deville 64 convertible

8 May 2, 2020
Reply by JOHN V SCHILLACI

"Hello, I have one that was repaired. I'm not sure if the weld is visible or not as I…"

JOHN V SCHILLACI replied Sep 9, 2019 to Exhaust manifold: Repair, replace or headers?

10 Sep 14, 2019
Reply by Tony and Ginny 429

"Hello, As far as I know there are 2 trunk hinge tension rods that hold that open. Th…"

JOHN V SCHILLACI replied Aug 29, 2018 to Trunk won’t stay up!

8 Feb 27, 2020
Reply by Jason Edge

"The car is located in Whiting, Indiana ,  46394.  It's about 40-50 miles south of do…"

JOHN V SCHILLACI replied Jun 12, 2018 to WTB or Trade...

8 Jun 17, 2018

RSS

Photos

  • Add Photos
  • View All

Forum

Whoa there, you want how much??

Started by Robert Gonzalez in 1963/64 Cadillac Specific Discussion 15 hours ago. 0 Replies

Ok, I’ve been on here for almost a decade. I KNOW we covet our cars and have always tried selling them at premium prices. But the bottom line, our cars rarely fetched prices over a covair. The…Continue

1964 Cadillac parts for sale... northern cali

Started by Jason in For Sale. Last reply by Jeremy yesterday. 1 Reply

Bill Hirsch cast iron gray exhaust and manifold paint (1 can) $20Bill hirsch Cadillac dark blue engine enamel high temp high gloss (2 cans) $40Convertible top latchValve coversHeadlight bezelRadioGas…Continue

Tags: Parts

63 4 door Cadillac

Started by Walt Timmerman in For Sale. Last reply by Jeremy yesterday. 7 Replies

Need to start parting this car out. Might be moving soon and if its not parted out, it'll be scrapped.Also have Motor and transmission from my 63 coupe deville for sale. will part out also.Was told…Continue

Free- 64 lower bumper bucket - Passenger side

Started by Michael Buonaccorso in For Sale. Last reply by Jeremy yesterday. 1 Reply

This is in rough shape. Not only is there rust in the usual places but it is also bent. I replaced this piece on my car after an accident, but since this is a hard to come by piece, I figured someone…Continue

Blog Posts

Rumble Sound at 55-60 mph

Posted by Ray Schick on September 20, 2021 at 10:45pm 6 Comments

64 Coupe DeVille , while driving at 55-60 mph I have a oscillating rumble sound . Steering wheel does not shake or vibrate . Transmission mount looks good .Tires were replaced 2 years ago balanced and rebalanced recently. Axel bearings were just replaced, rear differential assembly was just replaced with a Posi track ,pinion bearings good. Fresh gear lube. Driveshaft checked and balanced the other day ,new center bearing installed and new bearing carrier assembly too. Trying to figure this…

Continue

1963 series 62 convertible transmission issue

Posted by Matthew VanDeWater on June 22, 2021 at 3:03pm 1 Comment

Hello I've been restoring a 63 for way to many years. Down to almost done, but have issue with trans linkage, when column in park shift rod 2 inches short. everything original. been trying to find picture of manual rod hooked up from under car to see position of linkage. was wondering if anybody has access for pictures. I wanted to see if my manual linkage is bent  wrong out of the trans if somebody dropped the trans or something. Doesn't make sense why it doesn't work. Thanks for any input…

Continue

New vehicle in the club

Posted by Patrick Westphal on June 17, 2021 at 4:00pm 1 Comment

I was successful in getting a vehicle from the New York contact I talked about at the last club meeting. I am still trying to figure out how to post a picture of the vehicle that is tied with this comment so if you see a random picture of a black convertible in a yard, that's me haha.  …

Continue

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service