paul k's Discussions (83)

Discussions Replied To (44) Replies Latest Activity

"Thank you very much. Paul"

paul k replied Sep 3 to 2 pieces for front bumper.

4 Sep 3
Reply by paul k

"Is this the right place in the picture?And the shim placement has to be specific way…"

paul k replied Sep 3 to 2 pieces for front bumper.

4 Sep 3
Reply by paul k

"Thank you, Paul"

paul k replied Aug 12 to Hood to cowl side seals position.

2 Aug 12
Reply by paul k

"Thank you, Paul"

paul k replied Aug 12 to fender bracket support?

2 Aug 12
Reply by paul k

"Ok,problem solved. When I installed the knobs on the radio I push the top knob too f…"

paul k replied Aug 12 to Power antenna problem.

12 Aug 12
Reply by Tony and Ginny 429

"It is only react when I pull up."

paul k replied Aug 11 to Power antenna problem.

12 Aug 12
Reply by Tony and Ginny 429

"The antenna is original from the car -not new.Maybe the radio knob I installed diffe…"

paul k replied Aug 11 to Power antenna problem.

12 Aug 12
Reply by Tony and Ginny 429

"I did not know where they were attached because mine were gone.Thank you for the pic…"

paul k replied Jul 26 to Inner fenders apron question.

2 Jul 26
Reply by paul k

"Hi Shane, no -it is between molding attached to the roof above side door windows."

paul k replied Jul 25 to Roof molding question.

3 Jul 25
Reply by paul k

"Ok, I did remove ball joint with another tool from harbor.."ball joint separator" $1…"

paul k replied Apr 11 to upper ball joint removal

6 Apr 12
Reply by Ronnie Lay

RSS

Photos

  • Add Photos
  • View All

Forum

STEERING GEAR

Started by Kim K Kaiser in 1963/64 Cadillac Specific Discussion. Last reply by Mark S Anderson 2 hours ago. 12 Replies

IN addition to the main seal leak,,which i am going to tackle again tomorrow,i also have a leak in what seems to be the steering gear.  I have checked to connections from the pump, and its dry on…Continue

What front springs to use to level car back out after an LS swap?

Started by Richard Biele in 1963/64 Cadillac Specific Discussion 9 hours ago. 0 Replies

I see other members have put LS engines into their cars. I am wondering what springs you put in afterwards. I cannot determine the height due to the car having a front end fire (how I ended up with…Continue

2020 Cadillac calendars.

Started by Russ Austin in General Discussion 12 hours ago. 0 Replies

I just got in the 2020 Classic Cadillac calendars.  12 months of 63-64…Continue

Henry Leland- founder of Cadillac and Lincoln

Started by Kurt in 1963/64 Cadillac Specific Discussion. Last reply by Jason Edge yesterday. 2 Replies

Here's a good article about Henry Leland. I had heard bits & pieces of his story over the years but didn't know all these details.…Continue

Blog Posts

driveshaft help

Posted by wayne weaver on October 9, 2019 at 4:41pm 1 Comment

can anyone help me with a driveshaft ? I have a 1963 Cadillac 62 series 4dr with the hydro-matic trans. I need the male splined shaft on the front of the rear driveshaft section. the piece with the nut attached by clip.id be willing to buy a shaft if its not horribly priced.

Dash removal

Posted by Jake Mickley on October 9, 2019 at 12:06am 9 Comments

Hello everyone,

On a 63 CDV, if a guy wanted to remove the entire dash to get all the metal painted, and do some other things behind there, how would he go about doing that?  I checked here and the shop manual, but can't find a complete guide.

As always, and help or direction is appreciated.  Thanks!

--Jake

Introducing myself

Posted by Gary Marchand on October 7, 2019 at 9:32pm 8 Comments

Thanks for letting me join the club.  Picked up this ‘64 Coupe Deville a few months ago out of Beverly MA, the car has few stickers on it from various Cadillac clubs, didn’t know if anyone might recognize it from it’s “Glory days.” Everything seems pretty healthy except for the body and some very Mickey Mouse repairs, was wondering if anyone had any leads on…

Continue

Carter AFB carburetor question

Posted by Ray Schick on October 7, 2019 at 8:29pm 8 Comments

3655S carb, and a 3656S carb .I know the difference is one is for A/C and the other in for a non A/C car . Now the question is : can I use the carb bowl from the A/C car on the non A/C car ? They look the same set up next to each other

Videos

  • Add Videos
  • View All

© 2019   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service