Kevin Campbell's Discussions (1,495)

Discussions Replied To (1366) Replies Latest Activity

"Hi Chris, I see you are in NZ. Almost an outer suburb of Australia, being just acros…"

Kevin Campbell replied Aug 16, 2020 to 64 SDV axle bearings

16 Aug 16, 2020
Reply by Chris Cheveau

"I had a solid look at this and it turns out, going there, you were going against the…"

Kevin Campbell replied Jul 31, 2020 to Mpg

8 Aug 3, 2020
Reply by Tony and Ginny 429

"and...... after all the bushfires and shit last year, we seem to be handling the cov…"

Kevin Campbell replied Jul 6, 2020 to Winter time cruise in Australia.

4 Jul 6, 2020
Reply by Kevin Campbell

"Its a nice place, much bigger than most people think too. We also have some pretty g…"

Kevin Campbell replied Jul 6, 2020 to Winter time cruise in Australia.

4 Jul 6, 2020
Reply by Kevin Campbell

"Bit early..... Father's day is 1st Sunday in September. (in Australia at least)"

Kevin Campbell replied Jun 22, 2020 to Happy Father's day to all the Dads, and to the Dad's that Inspired Us

4 Jun 22, 2020
Reply by Jason Edge

"My pleasure Kurt.... and I do mean..... pleasure."

Kevin Campbell replied May 25, 2020 to Oil Pan Gaskets

17 May 26, 2020
Reply by Kim K Kaiser

"Oh man, I love it when you talk dirty. LOL"

Kevin Campbell replied May 25, 2020 to Oil Pan Gaskets

17 May 26, 2020
Reply by Kim K Kaiser

"We haven't R12 in Australia for ages now. Three years ago I gassed up on R437A, that…"

Kevin Campbell replied May 22, 2020 to How to change AC compressor shaft seal?

17 Jul 22, 2020
Reply by Christian Doerk

"I think i heard, some gases will eat the seals over time. I might have to upgrade to…"

Kevin Campbell replied May 21, 2020 to How to change AC compressor shaft seal?

17 Jul 22, 2020
Reply by Christian Doerk

"I'm keen to know this one as well. Mine has started to weep there."

Kevin Campbell replied May 21, 2020 to How to change AC compressor shaft seal?

17 Jul 22, 2020
Reply by Christian Doerk

RSS

Photos

  • Add Photos
  • View All

Forum

Very sensitive brakes.

Started by Phil in 1963/64 Cadillac Specific Discussion. Last reply by Phil 9 hours ago. 18 Replies

Hey everyone,  how sensitive should the power brakes be?  I have just rebuilt the power booster and  replaced the master cylinder. The pedal doesn’t have any resistance so I have to be very gentle so…Continue

New Batch of Embroidered Iron-On 1963/64 Cadillac Chapter Patches - $4 each

Started by Jason Edge in Chapter Discussion. Last reply by Jason Edge 9 hours ago. 8 Replies

As noted in our August 1963/64 Cadillac Chapter Newsletter:Around 6 years…Continue

Tags: Available, Patches, Chapter, Cadillac, 1963/64

63 rear main seal

Started by Luther in 1963/64 Cadillac Specific Discussion. Last reply by Tony and Ginny 429 16 hours ago. 9 Replies

Hello all , just spent better part of the weekend installing a new rear main seal and pan set on my 63 390 , all though it slowed the leak down considerably , l still have a drip , l used a Felpro…Continue

Current 1963/64 Cadillac Listings on eBay

Started by Jason Edge in For Sale. Last reply by Jason Edge 20 hours ago. 0 Replies

To see all 1963/64 Cadillacs Listed on eBay in the USA…Continue

Tags: ebay

Blog Posts

Torque converter grab when idling in Drive

Posted by Cliff Johnston on June 14, 2021 at 8:47pm 2 Comments

Hi Everyone, been quite a while since i have been on here.

I have had an issue with the idle on my 64 Coupe Deville ever since i have had it.

With the Idle set high enough that it is smooth, but still a nice idle, the RPM seems only slightly too high for the stall of the Torque Converter. And therefore it tends to sit there and grab and lunge a bit. So until now, i have been putting the car in Neutral at the lights to stop this happening.

I've had the car dyno tuned and…

Continue

Can you help? Driveshaft Question....

Posted by Chris on May 30, 2021 at 8:55am 1 Comment

Hello!

Newbie to the group here - we have already found tons of invaluable information on the board, so thanks! We are restoring a 1963 Series 62 Convertible. We are wondering if anyone knows of a source to buy the propellor yoke flange (that bolts to the pinion flange) for the driveshaft? One of our ears partially broke off. Not sure if we can buy just the yoke flange as an aftermarket part, or if it has to be rebuilt by a welder/fab guy? Maybe a salvage yard for a source? Again, any…

Continue

Thank you Kurt re: VIN location

Posted by Robert Pellow on April 19, 2021 at 1:07pm 0 Comments

I just wanted to say a thank you to Kurt for steering me to the tech tips page on V.I.N. locations.  Excellent information.  Thanks a bundle.

Robert Pellow

V.I.N. where?

Posted by Robert Pellow on April 18, 2021 at 1:41pm 6 Comments

Where can I find the V.I.N. on a 63 convertible?  The usual space at the base of the interior windshield on the driver's side has been decimated by weather.

Events

Videos

  • Add Videos
  • View All

© 2021   Created by Jason Edge.   Powered by

Badges  |  Report an Issue  |  Terms of Service